Low pressure at one fixture is usually a clogged aerator or a partly closed stop valve. Low pressure everywhere points to the main shut-off, a pressure regulator, corroded pipe or a leak, or to the utility side of the meter. A few checks tell you which, and the rest is a job for a local plumber.
Weak water pressure is one of the most common plumbing complaints, and it has a lot of possible causes. The useful first question is where the problem shows up. If one faucet is weak, the cause is at that faucet. If the whole house is weak, the cause is in the main line, the regulator, the pipe material or the supply coming to your meter.
Start by sorting the problem: one fixture or the whole house
Run a cold tap at a few places: a kitchen sink, a bathroom sink, a hose bib outside. Then run the hot side at the same spots.
- One fixture, hot and cold both weak: the aerator or the cartridge is the likely cause.
- One fixture, only hot weak: look at the stop valve under the sink, then at the water heater side.
- Hot weak everywhere, cold fine: the trouble is at the water heater, its inlet valve or sediment buildup in the tank.
- Everything weak, hot and cold: the cause is upstream, at the main shut-off, a regulator, the service line or the utility.
Checks you can do in ten minutes
Unscrew the tip of a faucet and look at the aerator, the little screen that mixes air into the stream. In Tampa Bay, where finished water is moderately hard, a screen can fill with white or tan scale and pass only a trickle. Soak it in vinegar for an hour, rinse, and screw it back on. A showerhead behaves the same way and can be soaked in a bag of vinegar.
Next, check the valves. A stop valve under a sink that was bumped or only partly reopened after a repair can restrict flow. The main shut-off valve at the house should be fully open. A gate-style valve that was turned a quarter-turn and left there is a surprisingly common cause. If you are not sure where your shut-off is, the burst pipe first-10-minutes guide explains how to find it.
Finally, ask a neighbor or look at your water bill notes. If the street is weak, the cause may be outside your property, and the utility is the right call. Tampa Water, for example, lists a Utilities Call Center at (813) 274-8811 for outages and water quality questions. Other utilities in the area post their own numbers on their sites and bills.
Causes inside the house
Scale and corrosion in older supply pipe
Many Tampa Bay homes built before the 1980s have galvanized steel supply lines. Galvanized pipe rusts from the inside and narrows over time until a full-size pipe behaves like a straw. Typical signs are brown water after the line sits unused, pressure that has dropped slowly over years, and better flow at fixtures closest to the main. This is a replacement problem, not a cleaning problem, and it is one of the main reasons people look at repiping. Older neighborhoods such as Seminole Heights and Hyde Park have a good share of this stock, as do many mid-century homes in St. Petersburg and Clearwater.
Polybutylene, a gray plastic used in some homes from the 1980s into the mid-1990s, has its own history of failures at the fittings, so it is worth knowing which material you have before deciding anything.
A failing pressure regulator
Some homes have a pressure-reducing valve, a bell-shaped brass fitting near the main shut-off. It holds street pressure down to a level the house can handle. When it wears out, pressure can drop or swing, and you may hear a hammering when a tap closes. A plumber can read a gauge on a hose bib and tell you quickly if the regulator is the problem. Homes with no regulator should not be assumed to have one. Many Tampa Bay houses simply take whatever arrives at the meter.
A leak you have not found
A leak between the meter and the house, or under the slab, steals pressure before the water reaches your fixtures. Signs include a meter that keeps moving with every fixture off, a wet or unusually green patch in the yard, a warm spot on a slab floor, or the sound of running water in a quiet house. Pressure loss with a rising water bill is a strong clue. The slab leak guide covers the in-slab version, and leak detection and water line repair are the services that find and fix the others.
Water heater and sediment
If only hot water is weak, sediment inside the tank or a partly closed inlet valve may be the cause. Hard water speeds up that scale. Tankless units can also clog with scale and show reduced flow. The tank vs tankless guide goes into how each type handles hard water.
Clogged or undersized fixtures and irrigation
In-line filters, a clogged whole-house filter cartridge, or a water softener bypass left half open can reduce flow. Irrigation zones that share a supply with the house can also pull pressure down while they run. If the pressure is weak only when the sprinklers are on, you have your answer.
Causes outside the house
Between the street main and your door there are several pieces: the utility's main, the curb stop, the meter, and your private line. In Tampa, the City owns the curb stop, the meter box sits near the property line, and the customer's private shut-off is usually between the meter box and the house. Everything on your side of the meter is yours to repair.
A partly closed or failing curb stop, a corroded private service line, or a damaged meter setup can all cut flow. Only the utility can work on its own equipment, and only a plumber can work on yours, so the first step is figuring out which side the problem is on. A plumber can test pressure at a hose bib and compare it with what the utility says should be arriving.
Utilities also flush hydrants, repair mains and shift supply in ways that can lower pressure for a few hours. If the weak pressure started suddenly and the neighbors have it too, wait a short time and call the utility rather than a plumber.
Hard water, scale and pressure
Tampa Bay water is moderately hard to hard depending on the utility. Over years, scale narrows pipe, clogs aerators and coats heater elements. If your pressure problem keeps returning at the faucets, hardness may be the common thread. The hard water guide explains what the local numbers look like and what softening does and does not fix.
Too much pressure is also a problem
Not every pressure complaint is about weakness. Very high pressure can cause toilet fill valves to hiss, hoses to burst and water hammer. If you are chasing a spike rather than a drop, a gauge screwed onto a hose bib will show the actual number, and a plumber can tell you whether a regulator or an expansion tank is in order.
When to stop and call a plumber
Call when the problem is whole-house and the quick checks did not change anything, when the water is brown, when you suspect a leak, when you have galvanized or polybutylene pipe, or when pressure changes suddenly with noise from the walls. Work on supply lines, regulators and anything inside a wall or slab is not a good DIY project. Permits for larger work such as repiping go through the building department that covers your address, so ask the plumber how that will be handled.
When you call the number on this page, you are connected with an independent local plumber, and you can describe what you have already tried. Plumber Tampa is a referral service, not a plumbing company, so the plumber you speak with gives you the scope and the price for your house. If the weak flow is only at a single fixture, faucet repair is often enough. If it is a whole-house issue in a town outside the city, browse the service areas or all plumbing services. For home owners in the suburbs, the same troubleshooting applies in Brandon and Clearwater.
Frequently asked questions
Why is the water pressure low only in the shower?
Can hard water cause low pressure?
Should I call the utility or a plumber for low pressure?
Sources
Last updated: